---
title: "Why not wire a radio to both of its antennas?"
topic: "Switch connector"
answer: "Because the power splits. With a PCB antenna and a cable both wired to the radio, 46% of its power reaches the cable, 39% goes to the PCB antenna and 14% bounces back. A switch connector sends about 96% to the cable, and it switches itself when the plug goes in."
url: "https://nearfieldnotes.com/notes/switch-connector/"
site: "Near Field Notes"
author: "Michael Walker"
note: 32
family: "RF"
published: "2026-11-12"
revised: "2026-11-12"
revision: 1
video: "https://nearfieldnotes.com/videos/switch-connector/"
---

Note 32 · [RF](https://nearfieldnotes.com/families/rf/) · Rev 1 · [Watch the video · 2:06](https://nearfieldnotes.com/videos/switch-connector/)

Switch connector

# Why not wire a radio to both of its antennas?

**Short answer:** Because the power splits. With a PCB antenna and a cable both wired to the radio, 46% of its power reaches the cable, 39% goes to the PCB antenna and 14% bounces back. A switch connector sends about 96% to the cable, and it switches itself when the plug goes in.

Unplug the cable and the empty branch still costs. On this board it lets 83% through to the PCB antenna at 2.4 GHz and 0.5% at 5.5 GHz.

A 0 Ω resistor or an RF switch chip can pick the antenna too. Each suits a different product.

**Note 32’s opening figure: One radio, two antennas.** Where the power goes with the cable plugged in

![Note 32’s opening figure: One radio, two antennas](https://nearfieldnotes.com/notes/switch-connector/fig-opening.png)

*What the figure shows:* Where the radio's power goes with the cable plugged in. With a PCB antenna and a cable both wired to the radio, 46% reaches the cable, 39% goes to the PCB antenna and 14% bounces back to the radio, simulated at 2.45 GHz. With a switch connector, about 96% reaches the cable, at most 1% leaks to the PCB antenna and about 3% bounces back, from I-PEX's limits for the part.

Each band is as wide as its share of the radio’s power. Both wired is simulated on this page’s board. The switch connector’s shares come from I-PEX’s limits for its MHF-SW23, so a typical part does a little better.

**The numbers**

*Shares of the power the radio sends, with the cable plugged in. The switch connector’s row leaves out the board’s traces.*

|  | To the cable | To the PCB antenna | Back to the radio | Lost |
|---|---|---|---|---|
| Both wired, simulated at 2.45 GHz | 45.6% | 39.0% | 14.1% | 1.3% |
| Switch connector, I-PEX’s limits to 3 GHz | 96.0% or more | 1.0% at most | 2.8% at most | 0.2%, a 100 mΩ contact |

## The board and its two antennas

*34 × 24 mm, 4 layers*

A 2.4 GHz radio module, U1, sits on the left of the board. Its PCB antenna, ANT1, is printed in the copper on the right. It is the meandered inverted-F from TI’s AN043, the antenna of [Note 3](https://nearfieldnotes.com/notes/antenna-ground/).

J1 is a U.FL connector for an external antenna on a cable. A product like this ships with the PCB antenna working, and a cable goes in when it needs more range or sits inside a metal box.

The easy layout is a tee. One trace leaves the radio, and at a junction it goes both ways, so both antennas stay wired all the time.

**Fig. 32a: One radio, wired to both.**

![Fig. 32a: One radio, wired to both](https://nearfieldnotes.com/notes/switch-connector/fig-32a.png)

*What the figure shows:* Figure 32a: the 34 by 24 mm board rendered from above its front edge. A shielded radio module is on the left and a meandered PCB antenna is printed in the copper on the right. One trace leaves the radio and splits at a tee: straight on to the PCB antenna, and down a short branch to a U.FL connector with an antenna cable plugged into it.

The board with the cable plugged in. The trace from the radio is drawn in black, the way to the PCB antenna in orange and the branch to the cable in blue.

**The numbers**

| Part | What it is |
|---|---|
| U1 | 2.4 GHz radio module under its shield |
| Y1 | Its crystal |
| ANT1 | PCB antenna: a meandered inverted-F printed in the top copper, the outline from TI’s AN043 |
| J1 | U.FL connector for an external antenna, with a 1.13 mm coax cable plugged in |
| Trace | 50 Ω microstrip, 0.373 mm wide: 5.5 mm from the radio to the tee, 7.5 mm on to the PCB antenna, 6 mm down the branch to J1’s pad |

As a circuit it is three pieces of [50 Ω](https://nearfieldnotes.com/glossary/#g-characteristic-impedance) trace meeting at one point. The radio’s is 5.5 mm long. The PCB antenna is 7.5 mm past the junction, and J1’s pad is 6 mm down the branch.

That leaves two cases to check: the cable plugged in, and the cable out.

**Fig. 32b: The tee, as a circuit.**

![Fig. 32b: The tee, as a circuit](https://nearfieldnotes.com/notes/switch-connector/fig-32b.png)

*What the figure shows:* Figure 32b: the board as a circuit. The radio, U1, drives a 50 ohm trace 5.5 mm long to a junction. From there one trace runs 7.5 mm to the PCB antenna, ANT1, and a second runs 6 mm to J1, a U.FL connector for the cable, whose shell is grounded.

Every trace is 50 Ω microstrip, 0.373 mm wide, on JLCPCB’s common 4-layer stack. The colors match Fig. 32a.

## Both wired, the power splits

*Cable in, 2.45 GHz*

At the junction the radio’s 50 Ω trace meets two 50 Ω loads side by side, and together they look like 25 Ω. A wave that meets a different impedance partly [bounces back](https://nearfieldnotes.com/glossary/#g-reflection):

`Γ = (Z_L − Z_0)/(Z_L + Z_0)`

where Γ: reflection coefficient at the junction (No unit); Z_L: the load at the junction: the two antennas in parallel (Ω); Z_0: the trace’s characteristic impedance (Ω).

`= (25 Ω − 50 Ω)/(25 Ω + 50 Ω) = −1/3`

The share of the power that bounces is that number squared:

`P_back/P = Γ^2`

where P_back: power that bounces back to the radio (W); P: power the radio sends (W); Γ: reflection coefficient at the junction (No unit).

`= (1/3)² = 1/9 = 11.1%`

The other 88.9% splits evenly, 44.4% each way. That is an ideal tee. On the board, the branch ends in J1’s 1 × 1 mm pad, which is a small capacitor to the ground under it. It makes the branch look lower than 50 Ω, so the branch takes more than its half and more bounces back.

**Fig. 32c: Where the power goes.**

![Fig. 32c: Where the power goes](https://nearfieldnotes.com/notes/switch-connector/fig-32c.png)

*What the figure shows:* Figure 32c: where the radio's power goes at 2.45 GHz with both antennas wired and the cable plugged in. 45.6% reaches the cable, 39.0% the PCB antenna, 14.1% bounces back to the radio and 1.3% is lost in the board. An ideal tee would send 44.4% each way and reflect 11.1%.

Shares of the power the radio sends into its trace, with the cable plugged in, at 2.45 GHz. An ideal tee loses nothing, so it has no fourth tick.

**The numbers**

*Shares of the power the radio sends into its trace, cable plugged in.*

|  | Cable | PCB antenna | Back | Lost |
|---|---|---|---|---|
| Ideal tee, two 50 Ω loads | 44.4% | 44.4% | 11.1% | 0 |
| Simulated, 2.45 GHz | **45.6%** | **39.0%** | **14.1%** | 1.3% |
| Simulated, 5.5 GHz | 44.8% | 36.6% | 15.0% | 3.6% |
| Same tee without J1’s pad, 2.45 GHz | 43.6% | 43.6% | 11.5% | 1.3% |
| A 50 Ω line past the pad as the cable, 2.45 GHz | 45.2% | 40.0% | 13.5% | 1.3% |
| Finer mesh, 2.45 GHz | 45.6% | 39.0% | 14.1% | 1.3% |

Tee junction

### 46% to the cable, 39% to the other antenna

**Field marks.** With the cable in, 46% of the radio’s power reaches it. 39% goes to the PCB antenna, 14% bounces back to the radio and 1.3% is lost in the board.

**Look-alike.** A 3 dB splitter. A tee is said to cost half the power. It costs a little more, because it reflects as well as splits: an ideal tee delivers 44.4% each way, 3.5 dB down.

**Range.** At 5.5 GHz the split is 45% to the cable, 37% to the PCB antenna and 15% back. The same tee without J1’s pad gives 43.6%, 43.6% and 11.5% at 2.45 GHz, close to the ideal.

**Habitat.** Boards that offer a PCB antenna and a connector, and leave both wired so nothing has to be chosen at the factory.

## Cable out, the branch is a stub

*Nothing plugged in*

Unplug the cable and the branch ends at J1’s empty pad. A trace that leads nowhere is a stub. The wave runs down it, bounces off the open end and comes back to the junction.

When the trip down and back takes half a cycle, the returning wave cancels the one at the junction. The junction then looks like a short, and nearly all of the power bounces back to the radio. That happens when the stub is a quarter of a wavelength long:

`L_¼ = c/(4 f √(ε_eff))`

where L_¼: length of a quarter-wave stub (m); c: speed of light (m/s); f: frequency (Hz); ε_eff: effective permittivity the wave sees (No unit).

`= (3.00 × 10⁸ m/s)/(4 × 5.5 GHz × √(3.23)) = 7.58 mm`

J1’s pad makes the stub act 1.4 mm longer than its trace, so at 5.5 GHz the dip comes at 6.2 mm of branch. This board’s branch is 6 mm.

**Fig. 32d: The empty branch.**

![Fig. 32d: The empty branch](https://nearfieldnotes.com/notes/switch-connector/fig-32d.png)

*What the figure shows:* Figure 32d: the tee seen close, with nothing plugged into J1. The trace from the radio runs left to right across the top, on its way to the PCB antenna. The branch leaves it at a right angle and runs 6 mm down to the signal pad of the empty U.FL connector.

The tee with nothing plugged into J1. The way to the PCB antenna is drawn in orange and the branch in blue.

**Fig. 32e: Against the branch’s length.**

![Fig. 32e: Against the branch’s length](https://nearfieldnotes.com/notes/switch-connector/fig-32e.png)

*What the figure shows:* Figure 32e: the share of the radio's power that reaches the PCB antenna with the cable out, against the length of the empty branch from 0 to 25 mm. At 2.45 GHz it falls from 98% with no branch to almost nothing at 15.5 mm, then recovers. At 5.5 GHz it falls to almost nothing at 6.2 mm, recovers, and dips again at 21.3 mm. At this board's 6 mm, 83% arrives at 2.45 GHz and 0.5% at 5.5 GHz.

Cable out. The share of the radio’s power that reaches the PCB antenna as the empty branch gets longer. The dotted line marks this board’s 6 mm.

**The numbers**

*Cable out. 43 lengths were simulated; these are 15 of them.*

| Branch | 2.45 GHz, arrives | Bounces back | 5.5 GHz, arrives | Bounces back |
|---|---|---|---|---|
| 0 mm | 98.1% | 0.0% | 95.8% | 0.0% |
| 1 mm | 96.6% | 1.3% | 88.8% | 7.0% |
| 2 mm | 95.1% | 2.7% | 80.4% | 15.3% |
| 4 mm | 90.6% | 7.0% | 45.6% | 49.6% |
| 6 mm | 83.0% | 14.3% | 0.5% | 92.6% |
| 6.18 mm | 82.2% | 15.1% | 0.1% | 92.9% |
| 8 mm | 71.3% | 25.8% | 36.3% | 56.0% |
| 10 mm | 53.6% | 43.0% | 75.6% | 17.3% |
| 12 mm | 30.1% | 65.9% | 90.5% | 2.9% |
| 14 mm | 7.2% | 88.2% | 93.3% | 0.1% |
| 15.54 mm | 0.1% | 94.9% | 89.4% | 3.8% |
| 18 mm | 16.7% | 78.4% | 66.2% | 25.2% |
| 20 mm | 41.3% | 54.2% | 21.2% | 66.4% |
| 21.32 mm | 55.6% | 40.0% | 0.5% | 84.2% |
| 25 mm | 81.6% | 14.4% | 70.9% | 18.5% |

Open stub

### 83% at 2.4 GHz, 0.5% at 5.5 GHz

**Field marks.** With the cable out, this board’s 6 mm branch lets 83% of the radio’s power reach the PCB antenna at 2.45 GHz. At 5.5 GHz 0.5% gets there and 93% bounces back.

**Look-alike.** A bad antenna. The board works at 2.4 GHz and is nearly deaf at 5 GHz, so the antenna gets the blame. Plug the cable in and the same board sends 45% into it at 5.5 GHz.

**Range.** The dips are at 6.2 mm for 5.5 GHz and 15.5 mm for 2.45 GHz, with a second 5.5 GHz dip at 21.3 mm. Less than 10% arrives across 1.7 mm of length around the first and 3.7 mm around the 2.45 GHz one. Even 1 mm of branch costs something: 96.6% arrives at 2.45 GHz and 88.8% at 5.5 GHz, against 98.1% and 95.8% with no branch.

**Habitat.** Dual-band Wi-Fi boards with an unused antenna connector at the end of a few millimeters of branch.

Hold the branch at 6 mm and sweep the frequency, and the stub shows up as a notch at 5.63 GHz. The 5 GHz Wi-Fi band runs from about 5.2 to 5.8 GHz, so the notch sits inside it.

A shorter branch moves the notch up and a longer one moves it down. Size the branch yourself, at the end of this note, draws any length.

**Fig. 32f: Against frequency.**

![Fig. 32f: Against frequency](https://nearfieldnotes.com/notes/switch-connector/fig-32f.png)

*What the figure shows:* Figure 32f: the share of the radio's power that reaches the PCB antenna with the cable out and a 6 mm branch, against frequency from 0.5 to 7 GHz. It falls slowly from nearly all of it at 0.5 GHz to 83% at 2.45 GHz, then into a notch that bottoms out at 5.63 GHz, where 0.06% arrives. At 5.5 GHz 0.5% arrives. A plain trace with no branch stays above 94% all the way.

Cable out. The share of the radio’s power that reaches the PCB antenna. The circles are 2.45 and 5.5 GHz.

**The numbers**

*Cable out. Share of the radio’s power that reaches the PCB antenna.*

| Frequency | 6 mm branch | No branch |
|---|---|---|
| 0.5 GHz | 98.8% | 99.6% |
| 1 GHz | 96.7% | 99.2% |
| 2 GHz | 88.8% | 98.5% |
| 2.45 GHz | 83.0% | 98.1% |
| 3 GHz | 73.4% | 97.7% |
| 4 GHz | 45.6% | 97.0% |
| 5 GHz | 10.2% | 96.2% |
| 5.5 GHz | 0.5% | 95.8% |
| 5.63 GHz, the notch | 0.06% |  |
| 6 GHz | 3.6% | 95.5% |
| 7 GHz | 34.7% | 94.7% |

## Inside a switch connector

*I-PEX MHF-SW23*

A switch connector goes in the trace where the tee was. It is 2.3 mm square and 1.35 mm tall, and it sits on two signal pads: one toward the radio and one toward the PCB antenna.

With nothing plugged in, the two pads are joined inside the part and the signal passes straight through to the PCB antenna. Push its plug in, and the radio feeds the cable while the PCB antenna is cut off.

These parts were made for factory testing. A probe pressed into one takes the radio’s output and disconnects the antenna, so the radio can be measured alone. I-PEX calls its part the MHF-SW23, Hirose the MS-156C and Murata the SWF.

**Fig. 32g: A switch connector.**

![Fig. 32g: A switch connector](https://nearfieldnotes.com/notes/switch-connector/fig-32g.png)

*What the figure shows:* Figure 32g: a switch connector, and the board with one in place of the tee. The part is a 2.3 mm square with a round gold shell on top, 1.35 mm tall, sitting on two signal pads. On the board it sits in the trace between the radio and the PCB antenna, with its right-angle plug and cable pushed into it.

The part on a piece of board, and the board of Fig. 32a with the part in place of its tee and its cable plugged in.

Inside is a spring, fixed at the radio’s end. Its free end presses up against a fixed contact on the antenna’s side.

The plug’s center pin comes down on the spring and pushes it off the contact. The radio now feeds the pin and the cable, and the fixed contact is left alone with the PCB antenna.

So the part has a direction. The spring’s end goes to the radio. Mounted backward, the plug would connect the cable to the PCB antenna and cut the radio off.

**Fig. 32h: Cut in half, plug going in.**

![Fig. 32h: Cut in half, plug going in](https://nearfieldnotes.com/notes/switch-connector/fig-32h.png)

*What the figure shows:* Figure 32h: a switch connector cut in half on a piece of board, in three steps. With no plug, a spring fixed on the radio side presses up against a fixed contact on the antenna side, and the signal runs from the radio's pad through the spring and the contact to the PCB antenna's pad. As the plug goes in, its center pin lands on the spring. With the plug seated, the pin holds the spring down, off the fixed contact, and the signal runs from the radio's pad along the spring, up the pin and out along the cable.

A simplified cutaway. The outside follows I-PEX’s drawing. The spring and the contacts are drawn from its description, and their shapes are estimates. The line is the signal’s path. It rests on the plug seated.

**Figure: What the maker guarantees.**

Fig. 32i

| Limit | As I-PEX states it | As power |
|---|---|---|
| Cable out, loss through the switch | 0.15 dB at most, to 2.5 GHz | 96.6% passes |
|  | 0.20 dB at most, to 6 GHz | 95.5% passes |
|  | 0.40 dB at most, to 11 GHz | 91.2% passes |
| Cable in, isolation to the PCB antenna | 20 dB at least, to 3 GHz | 1.0% leaks |
|  | 15 dB at least, to 6 GHz | 3.2% leaks |
|  | 12 dB at least, to 11 GHz | 6.3% leaks |
| Cable in, the plug’s VSWR | 1.4 at most, to 3 GHz | 2.8% bounces back |
|  | 1.6 at most, to 6 GHz | 5.3% bounces back |
|  | 2.0 at most, to 9 GHz | 11.1% bounces back |
| Plug-ins | 100 for the switch, 30 for the plug |  |

I-PEX’s limits for the MHF-SW23 and its plug harness. As power: the share a loss in dB still passes, the share an isolation in dB lets leak, and the share a VSWR reflects.

Switch connector

### About 96% to the cable

**Field marks.** Cable out, the switch passes at least 96.6% to the PCB antenna up to 2.5 GHz. Cable in, at most 1% leaks to the PCB antenna up to 3 GHz and the plug reflects at most 2.8%. Take off 0.2% more for a 100 mΩ contact, and about 96% is left for the cable.

**Look-alike.** A U.FL. Both are small square parts with a round shell on top, and people call this one a flow-through U.FL. A U.FL has no switch inside, and its plug doesn’t fit this part.

**Range.** Hirose’s typical curve for its MS-156C with the plug in reads 0.15 to 0.2 dB, so 95.5% to 96.6% passes. Its guaranteed limit is 0.5 dB to 3 GHz, or 89%. To 6 GHz I-PEX’s limits loosen: 95.5% passes with the cable out, and up to 3.2% leaks with it in.

**Habitat.** Wi-Fi and cellular boards that ship with a PCB antenna and offer an external one. Also test points: Nordic’s development kits put a Murata SWF in the antenna trace to measure the radio.

## Two other ways

*A resistor, or a chip*

A 0 Ω resistor picks the antenna with solder. The junction gets lands in both directions, and the resistor goes on the pair that leads to the antenna in use. Simulated toward the PCB antenna, 98.0% arrives, against 98.1% for a plain trace.

It is cheap and it loses almost nothing. Changing antennas takes a soldering iron.

An RF switch chip picks the antenna in firmware. A control pin chooses, even while the radio runs, so a product can try both and keep the better one. The chip needs power, a control line and a few capacitors, and a typical one loses 0.45 dB, about 10% of the power.

**Fig. 32j: The same junction, two other ways.**

![Fig. 32j: The same junction, two other ways](https://nearfieldnotes.com/notes/switch-connector/fig-32j.png)

*What the figure shows:* Figure 32j: the same junction built two other ways. In the first, a 0 ohm resistor marked R1 bridges the trace toward the PCB antenna, and an empty pair of lands beside it leads down the branch to the U.FL connector. In the second, a small RF switch chip marked U2 sits at the junction with a capacitor on each of its three RF pins, and control traces run to it from the radio.

R1 is an 0402 resistor on the lands toward the PCB antenna. The empty land below it leads to J1. U2 is an RF switch chip with a capacitor in each RF line and its control traces from the radio.

Side by side, only the tee loses half. The other three are within ten points of each other, so the choice comes down to who changes the antenna, and how.

The resistor is set once at the factory. The chip is set by firmware. The switch connector is set by whoever plugs in the cable, and it needs no firmware and no solder.

Its catch is wear. The plug is rated for 30 plug-ins and the switch for 100.

**Fig. 32k: Power that reaches the chosen antenna.**

![Fig. 32k: Power that reaches the chosen antenna](https://nearfieldnotes.com/notes/switch-connector/fig-32k.png)

*What the figure shows:* Figure 32k: the share of the radio's power that reaches the chosen antenna, four ways. Both wired, with the cable plugged in: 46%, simulated. A 0 ohm resistor: about 100%, simulated for the part alone. An RF switch chip: about 90%, from a typical datasheet loss of 0.45 dB. A switch connector: about 96%, from I-PEX's limits.

Both wired is simulated with the board’s traces in it. The other three are the part alone: one simulated, one from a typical datasheet figure and one from a maker’s limits.

**The numbers**

| Way | Reaches the antenna | From |
|---|---|---|
| Both wired | 45.6% | openEMS, cable plugged in, 2.45 GHz. Includes the board’s traces |
| 0 Ω resistor | 99.8% | openEMS: 97.95% with the resistor against 98.13% for a plain trace |
| RF switch chip | 90.2% | Abracon ASWD-S2-0008, 0.45 dB typical and 0.65 dB at most, 2.4 to 2.5 GHz |
| Switch connector | 96.0% | I-PEX MHF-SW23 limits to 3 GHz: 100 − 2.8 − 1.0 − 0.2 |

## Which cables fit

*A pin, where a U.FL has a socket*

A U.FL cable doesn’t fit a switch connector. A U.FL plug has a socket in its center, because the pin is in the U.FL connector on the board. A switch connector has no pin. Its plug has to bring one, to push the spring.

So the cable is the one made for the switch. I-PEX sells a plug on 1.13 mm coax for the MHF-SW23, part 20851, and lists it for antenna connection. Hirose sells the MS-156C-LP-068 for its MS-156C. Both are rated for 30 plug-ins, the same as a U.FL.

Murata’s SWF and SWG take only Murata’s test probes, so they serve as test points and can’t hold an antenna cable.

Hirose’s sheet also says the MS-156C is for testing a circuit only and cannot be used as an interface, on the same sheet that lists its antenna plug. Ask Hirose before making one a product’s antenna port.

**Fig. 32l: Two plugs, cut in half.**

![Fig. 32l: Two plugs, cut in half](https://nearfieldnotes.com/notes/switch-connector/fig-32l.png)

*What the figure shows:* Figure 32l: two cable plugs cut in half, each held above the same switch connector. The U.FL plug's center contact is a hollow socket, made to slide over a pin, so it has nothing to push the spring with. The switch connector's own plug carries a solid center pin that reaches down into the connector.

Each plug is held over the same switch connector, and the arrow marks its center contact. The U.FL plug’s socket has nothing to push the spring with. Simplified cutaways.

## Choosing a way

*Who changes the antenna*

Any of the three keeps nearly all of the power. What separates them is when the antenna gets chosen.

Key to antenna selection

### Resistor, chip or switch connector?

1. 1a The antenna is chosen once, at the factory 0 Ω resistor
2. 1b It can change after the board ships Go to 2
3. 2a Firmware chooses, or it changes while the radio runs RF switch chip
4. 2b Plugging in a cable chooses Switch connector

The board in Fig. 32a ends at 2b. Left as a tee, it gives up half its power with the cable in, and with the cable out its empty branch takes 5.5 GHz away.

## Size the branch yourself

*Cable out, 0 to 25 mm*

Set the length of the empty branch. The line is the share of the radio’s power that reaches the PCB antenna at each frequency, with the cable out.

The notch sits where the branch and its pad add up to a quarter of a wavelength. A longer branch brings it down in frequency, and from 17 mm a second notch comes into view.

**Note 32’s explorer: Reaches the PCB antenna, against frequency.**

![Note 32’s explorer: Reaches the PCB antenna, against frequency](https://nearfieldnotes.com/notes/switch-connector/fig-explore.png)

*What the figure shows:* The share of the radio's power that reaches the PCB antenna with the cable out, against frequency from 0.5 to 7 GHz, for the chosen length of empty branch. The dashed line is a plain trace with no branch. The circles are 2.45 and 5.5 GHz.

Each length is its own openEMS run, from 0.5 to 7 GHz. The circles are 2.45 and 5.5 GHz. The first notch is the lowest frequency where less than 10% arrives.

**The numbers**

*Cable out. Share of the radio’s power that reaches the PCB antenna.*

| Branch | At 2.45 GHz | At 5.5 GHz | First notch |
|---|---|---|---|
| 0 mm | 98% | 96% | None |
| 2 mm | 95% | 80% | Above 7 GHz |
| 4 mm | 91% | 46% | Above 7 GHz |
| 6 mm | 83% | 0.5% | 5.63 GHz |
| 8 mm | 71% | 36% | 4.42 GHz |
| 10 mm | 54% | 76% | 3.64 GHz |
| 12 mm | 30% | 91% | 3.10 GHz |
| 15 mm | 1.0% | 91% | 2.53 GHz |
| 20 mm | 41% | 21% | 1.94 GHz |
| 25 mm | 82% | 71% | 1.57 GHz |

#### Conditions

- **Board:** 34 × 24 mm, 1.6 mm thick, 4 layers. JLCPCB’s JLC04161H-7628 stack: 0.2104 mm of 7628 prepreg under the top layer, permittivity 4.4, loss tangent 0.018.
- **Traces:** 50 Ω microstrip, 0.373 mm wide: 49.4 Ω and an effective permittivity of 3.23 in the solve. Radio to the junction 5.5 mm, junction to the PCB antenna 7.5 mm, junction to J1’s pad 6 mm. The pad is 1.0 × 1.0 mm.
- **Solver:** openEMS, a 3D field solver, 117 runs. Cells are 0.025 mm at copper edges and 0.1 mm along the traces, with 4 through the prepreg.
- **Ends:** The radio, the PCB antenna and the cable are each a matched 50 Ω port. Copper is a perfect conductor, so the board’s loss is its FR-4’s: 0.063 dB/cm at 2.45 GHz and 0.142 dB/cm at 5.5 GHz.
- **Connector:** Only J1’s signal pad is in the model, without the connector’s body or its center contact. The cable is a 50 Ω port at the pad, and its own loss is left out.
- **Shares:** Of the power the radio sends into its trace. On this page 2.4 GHz means 2.45 GHz, the band’s middle.
- **Switch connector:** Not simulated. I-PEX’s limits for the MHF-SW23 to 3 GHz, as power: a plug VSWR of 1.4, 20 dB of isolation and a 100 mΩ contact.
- **RF switch chip:** Not simulated. Abracon’s ASWD-S2-0008, 0.45 dB typical from 2.4 to 2.5 GHz.
- **0 Ω resistor:** Simulated as a metal bridge the size of an 0402 on its lands. The part alone passes 99.8%: its run against the plain trace’s.
- **Checks:** A finer mesh moves no share by more than 0.15 points. With a 50 Ω line past the pad in place of the cable’s port, the tee gives 45.2%, 40.0% and 13.5%.
- **Renders:** Blender. The switch connector’s outside is from I-PEX’s drawing. Its inside is estimated.

Simulated only. Nothing on this page has been measured on a board yet.

#### Limits

- Real antennas aren’t 50 Ω across a band, and the split moves with them.
- With both wired, both antennas radiate at once. How the two add up in the air isn’t simulated.
- Real copper adds about 0.05 dB/cm at 2.45 GHz, as [Note 25](https://nearfieldnotes.com/notes/ufl-jumper/) found. On this board that is about half a point.
- A real U.FL connector adds a little more capacitance than its pad alone, so the dips would come at slightly shorter branches.
- The switch connector’s 96% is the part alone, built from limits. This board’s 5.5 mm of trace ahead of it would take 0.8% more.
- The limits are I-PEX’s, for one part. Other makers’ parts have their own.

#### Files

- layout.py The board: its stack, its traces and the four things that can sit at the junction
- sim/tee.py The openEMS model of the tee, the empty branch and the 0 Ω resistor
- sim/batch.py Every run on this page: the main cases, the 43 branch lengths and the checks
- sim/post.py Each run’s shares of power, and the sweeps against length and frequency
- sim/theory.py The transmission-line sums the runs are checked against
- render/board.py The board and its junction, four ways
- render/connector.py The switch connector, its plug and the cutaways

#### Sources

- [I-PEX, MHF-SW23 product specification PRS-1672, its loss, isolation and 100 cycles](https://www.i-pex.com/sites/default/files/downloads/pdf/PRODSPEC_MHF-SW23_PRS-1672-07EN.pdf)
- [I-PEX, MHF-SW23 plug harness 20851 specification PRS-2522, its VSWR and 30 cycles](https://www.i-pex.com/sites/default/files/downloads/pdf/PRODSPEC_MHF-SW23_PLUG_PRS-2522-03EN.pdf)
- [I-PEX, MHF-SW23 drawing 20549, its size and its two contacts](https://www.i-pex.com/sites/default/files/downloads/pdf/2D_MHF-SW23_ASSEMBLY_20549.pdf)
- [I-PEX, MHF-SW23 handling manual, its direction on the board](https://www.i-pex.com/sites/default/files/downloads/pdf/MANUAL_MHF-SW23_HIM-13004-04EN.pdf)
- [I-PEX, MHF-SW23 plug catalog, “For Antenna connection”](https://www.i-pex.com/sites/default/files/downloads/pdf/CATALOG_MHF-SW23_PLUG_E.pdf)
- [Hirose, MS-156C catalog, its loss, the MS-156C-LP-068 antenna plug and its precautions](https://www.mouser.lt/pdfDocs/MS-156C_Catalog_en_MS-156C_CAT.pdf)
- [Murata, switch connectors, the SWF and SWG and their probes](https://www.murata.com/en-us/products/connector/switchconnector)
- [Abracon, ASWD-S2-0008 RF switch datasheet, its 0.45 dB](https://mm.digikey.com/Volume0/opasdata/d220001/medias/docus/7469/ASWD-S2-0008-Datasheet.pdf)
- [Nordic, nRF52 development kit guide, its SWF connector for RF measurements](https://infocenter.nordicsemi.com/topic/ug_nrf52832_pdk/UG/nrf52_PDK/hw_rf_meas.html)
- [Hirose, U.FL series catalog, its 30 cycles](https://www.farnell.com/datasheets/3993933.pdf)
- [TI AN043, Small Size 2.4 GHz PCB Antenna](https://www.ti.com/lit/an/swra117d/swra117d.pdf)
- [JLCPCB, impedance calculator, the 7628 stack](https://jlcpcb.com/impedance)
- [Nan Ya NP-155F family datasheet, the 7628 prepreg’s 0.018](https://www.eurocircuits.com/content/uploads/2024/05/NP-155FTL_NP-155FR_NP-155FB.pdf)
- [openEMS, the 3D field solver](https://www.openems.de/)

What should the next note be? [Ask for one](https://nearfieldnotes.com/#ask-for-a-note)

---

Source: https://nearfieldnotes.com/notes/switch-connector/

Cite as: Michael Walker, “Switch connector”, Near Field Notes, Note 32, Rev 1, 12 Nov 2026. https://nearfieldnotes.com/notes/switch-connector/

Figures: free to reuse under CC BY 4.0 (https://nearfieldnotes.com/license/). Each one's image is linked under its name. Credit Michael Walker, Near Field Notes, and link the figure: this address plus #fig- and its number, like https://nearfieldnotes.com/notes/switch-connector/#fig-32a.
