---
title: "Should you drive a Peltier cooler with PWM or steady DC?"
topic: "Peltier coolers"
answer: "Steady DC. Simulated on a TEC1-12706 cooling a foam box from 12 V, unfiltered 50% PWM holds the box at 7.5 °C on 29.9 W. Steady DC at 4.68 V holds the same 7.5 °C on 7.4 W, a quarter of the power. A faster PWM doesn’t help. An inductor and a capacitor after the switch do."
url: "https://nearfieldnotes.com/notes/peltier-pwm/"
site: "Near Field Notes"
author: "Michael Walker"
note: 39
family: "Power"
published: "2026-11-14"
revised: "2026-11-14"
revision: 1
video: "https://nearfieldnotes.com/videos/peltier-pwm/"
---

Note 39 · [Power](https://nearfieldnotes.com/families/power/) · Rev 1 · [Watch the video · 3:05](https://nearfieldnotes.com/videos/peltier-pwm/)

Peltier coolers

# Should you drive a Peltier cooler with PWM or steady DC?

**Short answer:** Steady DC. Simulated on a TEC1-12706 cooling a foam box from 12 V, unfiltered 50% PWM holds the box at 7.5 °C on 29.9 W. Steady DC at 4.68 V holds the same 7.5 °C on 7.4 W, a quarter of the power. A faster PWM doesn’t help. An inductor and a capacitor after the switch do.

The heat a module pumps follows its average current. Its resistive heat follows the square of the current, so PWM pays for its peaks.

A Peltier module is a DC motor with no inductance. A motor smooths PWM into steady current by itself. A module can’t.

**Note 39’s opening figure: Two coolers, one box.** The box’s temperature and the power drawn, from switch-on

![Note 39’s opening figure: Two coolers, one box](https://nearfieldnotes.com/notes/peltier-pwm/fig-opening.png)

*What the figure shows:* Two Peltier coolers on the same foam box in a 25 °C room, simulated for 20 hours from switch-on. Both boxes pull down along the same curve and settle at 7.5 °C. The one on unfiltered 50% PWM from 12 V draws 35 W at first and 29.9 W once settled. The one on steady DC at 4.68 V draws 10.6 W at first and 7.45 W once settled, 4.0 times less.

Simulated. Both boxes cool along the same curve, so their two temperature lines lie on top of each other. The chart ends on both power lines, 20 hours in.

## A foam box with a cooler in its wall

*TEC1-12706, from 12 V*

Take a foam box of about 8 liters with six cans in it, in a 25 °C room. A cooler sits in one wall: a finned cold sink inside, an aluminum block through the foam, and a Peltier module, or [thermoelectric cooler](https://nearfieldnotes.com/glossary/#g-peltier-module), against a fan heatsink outside.

The module is a TEC1-12706, the 40 mm, 12 V part sold almost everywhere. Thermonamic’s datasheet rates it at 6.1 A and 16 V.

**Fig. 39a: The box, lid and front wall off.**

![Fig. 39a: The box, lid and front wall off](https://nearfieldnotes.com/notes/peltier-pwm/fig-39a.png)

*What the figure shows:* Figure 39a: the foam box rendered with its lid and front wall off. Six drink cans stand inside. The cooler sits in the right-hand wall: a finned cold sink inside, an aluminum block through the foam, the 40 mm module against the outer face, and a finned heatsink with a fan outside. Two leads hang from the module.

Rendered. The box leaks 0.42 W for each °C it sits below the room. The fan heatsink sheds heat at 0.30 °C per watt.

There are two ways to run it from 12 V. One is unfiltered PWM: a switch in series with the module, on for part of each cycle. It is the cheapest way to set the power.

The other is steady DC: a supply set to the voltage that holds the box at the same temperature. Here that is 4.68 V.

**Fig. 39b: The two drives.**

![Fig. 39b: The two drives](https://nearfieldnotes.com/notes/peltier-pwm/fig-39b.png)

*What the figure shows:* Figure 39b: the two drives as circuits. On the left, unfiltered PWM: a 12 V supply, the module and a switch in series, the switch closed half of each cycle, so the module sees 4.98 A or nothing. On the right, steady DC: a supply set to 4.68 V straight across the module, 1.59 A all the time.

In a real circuit the switch is a MOSFET. How fast it switches doesn’t change the result, as Fig. 39l shows.

## Inside the module

*254 legs in series*

A Peltier module is 254 small legs of bismuth telluride between two thin squares of ceramic. Copper tabs on the ceramic join the legs in series, so one current runs through all of them.

Half the legs are n-type and half are p-type, and they alternate. The current runs up an n leg, across a tab and down the next p leg.

**Fig. 39c: The module, cold side lifted off.**

![Fig. 39c: The module, cold side lifted off](https://nearfieldnotes.com/notes/peltier-pwm/fig-39c.png)

*What the figure shows:* Figure 39c: the TEC1-12706 rendered with its cold side lifted off. A square grid of small gray legs, 254 in all, stands on copper tabs on the white ceramic of the hot side. The red and black leads join the tabs at two corners of the hot side. The lifted ceramic of the cold side carries the part number on its top.

Rendered to Thermonamic’s drawing, 40 × 40 × 3.8 mm. Its sheet gives no leg size; these are 1.4 mm square, as in Kryotherm’s module of the same rating. The leads come off the hot side.

In an n leg the charge carriers are electrons, which move against the current. In a p leg they are holes, which move with it. So in every leg the carriers move the same way, from the cold side to the hot side.

They carry heat with them. That is the [Peltier effect](https://nearfieldnotes.com/glossary/#g-peltier-effect). In this module each amp carries about 15 W of heat, with the cold side at 5 °C.

**Fig. 39d: The front row of legs, up close.**

![Fig. 39d: The front row of legs, up close](https://nearfieldnotes.com/notes/peltier-pwm/fig-39d.png)

*What the figure shows:* Figure 39d: the front row of legs up close, rendered, with the cold side's ceramic out of the way. Each leg is a small block between a copper tab below and one above. The legs are tinted alternately as n-type and p-type, and arrows show the current running up each n leg and down each p leg, so it snakes through all of them in series.

Rendered. The tints mark the two kinds of leg. Real n and p legs look alike.

## Two taxes on every amp

*6.1 A, 40 °C across it*

The legs have resistance, about 2 Ω in all. The current heats them, and half of that heat ends up at the cold side.

Heat also leaks back through the legs, from the hot side to the cold side, in step with the temperature across them.

At 6.1 A with 40 °C across it, the current carries 87.0 W. Resistive heat takes back 37.5 W and the leak 22.0 W, which leaves 27.5 W pumped.

The heatsink gets all of it: the 27.5 W pumped plus the 88.4 W the module draws at 14.5 V. That is 115.9 W to shed for 27.5 W of cooling.

**Fig. 39e: The cold side’s heat budget.**

![Fig. 39e: The cold side’s heat budget](https://nearfieldnotes.com/notes/peltier-pwm/fig-39e.png)

*What the figure shows:* Figure 39e: the cold side's heat budget at 6.1 A with 40 °C across the module, hot face at 27 °C, simulated. The current carries 87.0 W from the cold side. Resistive heat takes back 37.5 W and heat leaking back through the legs another 22.0 W, leaving 27.5 W pumped.

From the fitted model, with the hot side held at 27 °C, the datasheet’s own test condition.

The heat carried grows with the current. The resistive heat grows with its square, so in the end it wins.

With 40 °C across it, this module pumps at most 28.5 W, at 7.1 A. With nothing to cool, its cold side gets coldest at 6.4 A: −43.5 °C. Push 10 A through it and the cold side only reaches −31.8 °C.

**Fig. 39f: The heat at the cold side, by current.**

![Fig. 39f: The heat at the cold side, by current](https://nearfieldnotes.com/notes/peltier-pwm/fig-39f.png)

*What the figure shows:* Figure 39f: the three heats at the cold side against current, with 40 °C across the module and its hot face at 27 °C, simulated. The heat the current carries climbs in a straight line, to 143 W at 10 A. The resistive heat landing on the cold side climbs with the square of the current, to 101 W at 10 A. The heat leaking back stays at 22.0 W. What is left, the heat pumped, peaks at 28.5 W at 7.1 A and falls after that.

From the fitted model, 40 °C across the module, hot side at 27 °C. Pumped is carried, less the other two.

## Read it like a DC motor

*Temperature is speed, heat is torque*

If you know DC motors, you know this part. A motor’s voltage is its current times its resistance, plus a back-EMF that grows with its speed.

*V* = *I*·*R* + *α*·Δ*T*

A module’s voltage is the same, with a back-EMF of about 55 mV for each °C across it. That is its [Seebeck coefficient](https://nearfieldnotes.com/glossary/#g-seebeck-coefficient), *α*. So the temperature across a module plays the part of speed, and the heat it pumps plays torque. [Note 40](https://nearfieldnotes.com/notes/peltier-generator/) runs the module backward, as a generator.

Stalled, with nothing across it, it pumps the most heat: 61.3 W, its [Qmax](https://nearfieldnotes.com/glossary/#g-qmax). Running free, with nothing to cool, it holds the most temperature across it: 70 °C, its [ΔTmax](https://nearfieldnotes.com/glossary/#g-delta-t-max). [Note 41](https://nearfieldnotes.com/notes/peltier-stack/) stacks modules to get past it.

At any one current, every load sits on the straight line between those two ends. The datasheet rates the module at the current that reaches ΔTmax and the voltage that takes, its [Imax and Vmax](https://nearfieldnotes.com/glossary/#g-imax-vmax).

**Fig. 39g: Heat pumped, by the temperature across it.**

![Fig. 39g: Heat pumped, by the temperature across it](https://nearfieldnotes.com/notes/peltier-pwm/fig-39g.png)

*What the figure shows:* Figure 39g: the heat the module pumps against the temperature across it, one straight line each at 1, 2, 3, 4 and 6.1 A, hot face at 27 °C, from the fitted model. At 6.1 A it pumps 61.3 W with nothing across it and reaches zero at 70 °C across. At 1 A the line runs from 15.3 W to zero at 26 °C.

From the model fitted to Thermonamic’s table and curves, hot side at 27 °C. The model lands within 0.85 W of the datasheet’s heat curves and 3.2% of its voltages.

**The numbers**

| Current | Pumped, 0 °C across | 20 °C across | 40 °C across | Zero at |
|---|---|---|---|---|
| 1 A | 15.3 W | 3.6 W | −8.8 W | 26 °C |
| 2 A | 28.6 W | 15.8 W | 2.5 W | 44 °C |
| 3 A | 39.7 W | 26.1 W | 11.7 W | 56 °C |
| 4 A | 48.9 W | 34.2 W | 18.9 W | 64 °C |
| 5 A | 55.9 W | 40.4 W | 24.1 W | 68 °C |
| 6.1 A | 61.3 W | 44.7 W | 27.5 W | 70 °C |

Like a motor, it works best lightly loaded. Its [coefficient of performance](https://nearfieldnotes.com/glossary/#g-cop), the heat pumped per watt drawn, peaks at 1.61 with 20 °C across it, at 1.58 A and 4.3 V. At 6.1 A it falls to 0.54.

With 40 °C across it the best is 0.48, at 3.3 A. Push more current and each extra watt buys less cooling.

**Fig. 39h: Heat pumped per watt, by current.**

![Fig. 39h: Heat pumped per watt, by current](https://nearfieldnotes.com/notes/peltier-pwm/fig-39h.png)

*What the figure shows:* Figure 39h: the heat the module pumps per watt it draws, against current, with 20, 40 and 60 °C across it and the hot face at 27 °C, from the fitted model. With 20 °C across it peaks at 1.61 at 1.58 A and falls to 0.54 at 6.1 A. With 40 °C the peak is 0.48 at 3.34 A, and with 60 °C 0.11 at 5.29 A.

From the fitted model, hot side at 27 °C. The dots are each line’s best.

**The numbers**

The best heat pumped per watt at each temperature difference, the model against the datasheet’s chart.

| Across the module | Best, model | Best, Thermonamic’s chart |
|---|---|---|
| 10 °C | 3.86 | 3.70 |
| 20 °C | 1.61 | 1.55 |
| 30 °C | 0.86 | 0.83 |
| 40 °C | 0.48 | 0.46 |
| 50 °C | 0.26 | 0.25 |
| 60 °C | 0.11 | 0.10 |

## Unfiltered PWM into the module

*50% duty from 12 V*

Now the two coolers. At 50% [duty](https://nearfieldnotes.com/glossary/#g-duty-cycle) the module gets the full 12 V half of the time: 4.98 A while on, nothing while off.

The heat it carries follows the average current, 2.49 A. Its resistive heat follows the square, so it heats like 3.52 A, the current’s rms. And while the switch is off, nothing pumps, but heat still leaks back.

The steady DC that holds the same box runs a flat 1.59 A.

**Fig. 39i: The current in the module.**

![Fig. 39i: The current in the module](https://nearfieldnotes.com/notes/peltier-pwm/fig-39i.png)

*What the figure shows:* Figure 39i: the current in the module as the switch turns on and off. On unfiltered 50% PWM it is 4.98 A for half of each period and nothing for the other half: 2.49 A on average, 3.52 A rms. Steady DC holding the same box is a flat 1.59 A.

Simulated, with the box settled at 7.5 °C. The PWM’s on-current is below 12 V over 2 Ω because the module’s back-EMF takes part of the 12 V.

The box settles at 7.5 °C on 29.9 W. Steady DC holds the same 7.5 °C, pumping the same 7.3 W out of the box, on 7.4 W.

Nearly all the difference is resistive heat: 25.4 W on PWM against 5.2 W on DC. The work of pumping is small in both, 4.5 W against 2.3 W.

The heatsink pays for it too. It takes 37.2 W on PWM and 14.8 W on DC, and runs at 36.2 °C against 29.4 °C.

**Fig. 39j: Where the power goes.**

![Fig. 39j: Where the power goes](https://nearfieldnotes.com/notes/peltier-pwm/fig-39j.png)

*What the figure shows:* Figure 39j: where the power goes when each drive holds the box at 7.5 °C, simulated. Unfiltered 50% PWM draws 29.9 W: 25.4 W of resistive heat in the legs and 4.5 W of work pumping heat uphill. Steady DC draws 7.45 W: 5.16 W of resistive heat and 2.29 W of work. Both pump the same 7.34 W out of the box.

Simulated. The work of pumping is the current times the module’s back-EMF.

**The numbers**

| Drive | Drawn | Resistive heat | Work of pumping | Pumped from the box | Into the heatsink | Hot face |
|---|---|---|---|---|---|---|
| PWM, 50% | 29.9 W | 25.4 W | 4.5 W | 7.3 W | 37.2 W | 36.2 °C |
| Steady DC | 7.4 W | 5.2 W | 2.3 W | 7.3 W | 14.8 W | 29.4 °C |

## At every duty, DC wins

*5% to 100%*

50% isn’t special. Every duty below 100% costs more than the DC that holds the same box.

At 25% PWM holds 15.4 °C on 16.1 W, where DC takes 1.8 W, 9 times less. At 75% it is 41.9 W against 19.1 W. The two meet at 100%, where PWM is just 12 V DC: −4.7 °C on 52.4 W.

Compare the 50% PWM with DC any other fair way and DC still wins. DC at the same average current cools the box to 1.4 °C on 17.8 W. DC at the same power cools it to −2.1 °C.

**Fig. 39k: The power that holds the box, by temperature.**

![Fig. 39k: The power that holds the box, by temperature](https://nearfieldnotes.com/notes/peltier-pwm/fig-39k.png)

*What the figure shows:* Figure 39k: the power that holds the foam box at each temperature, from 12 V, simulated: unfiltered PWM at every duty from 5 to 100%, and the steady DC that holds the same box. The PWM line lies above the DC line everywhere until they meet at 100%, where both are 12 V DC. At 50% duty PWM holds 7.5 °C on 29.9 W. Steady DC holds the same box on 7.45 W. DC at the same average current, 2.49 A, holds 1.4 °C on 17.8 W, and DC at the same 29.9 W holds -2.1 °C.

Simulated from 12 V. The PWM line runs through every duty in steps of 5%. The DC line is the steady voltage that holds the same box. Hollow dots: DC at the same average current and at the same power as the 50% PWM.

**The numbers**

| Duty | Box | PWM draws | PWM on | DC draws | DC at | PWM over DC |
|---|---|---|---|---|---|---|
| 5% | 22.9 °C | 3.4 W | 5.73 A | 0.07 W | 0.47 V | 48.9× |
| 10% | 20.9 °C | 6.8 W | 5.63 A | 0.28 W | 0.93 V | 24.1× |
| 15% | 19.0 °C | 10.0 W | 5.54 A | 0.63 W | 1.39 V | 15.8× |
| 20% | 17.1 °C | 13.1 W | 5.45 A | 1.1 W | 1.85 V | 11.6× |
| 25% | 15.4 °C | 16.1 W | 5.37 A | 1.8 W | 2.32 V | 9.1× |
| 30% | 13.7 °C | 19.0 W | 5.29 A | 2.6 W | 2.78 V | 7.4× |
| 35% | 12.1 °C | 21.9 W | 5.21 A | 3.5 W | 3.25 V | 6.2× |
| 40% | 10.5 °C | 24.6 W | 5.13 A | 4.6 W | 3.72 V | 5.3× |
| 45% | 9.0 °C | 27.3 W | 5.05 A | 5.9 W | 4.19 V | 4.6× |
| 50% | 7.5 °C | 29.9 W | 4.98 A | 7.4 W | 4.68 V | 4.0× |
| 55% | 6.1 °C | 32.4 W | 4.91 A | 9.2 W | 5.18 V | 3.5× |
| 60% | 4.7 °C | 34.9 W | 4.84 A | 11.2 W | 5.69 V | 3.1× |
| 65% | 3.4 °C | 37.3 W | 4.78 A | 13.4 W | 6.23 V | 2.8× |
| 70% | 2.2 °C | 39.6 W | 4.72 A | 16.0 W | 6.79 V | 2.5× |
| 75% | 0.9 °C | 41.9 W | 4.65 A | 19.1 W | 7.38 V | 2.2× |
| 80% | −0.3 °C | 44.1 W | 4.59 A | 22.6 W | 8.02 V | 1.9× |
| 85% | −1.4 °C | 46.3 W | 4.54 A | 27.0 W | 8.72 V | 1.7× |
| 90% | −2.6 °C | 48.4 W | 4.48 A | 32.4 W | 9.53 V | 1.5× |
| 95% | −3.7 °C | 50.4 W | 4.42 A | 39.8 W | 10.51 V | 1.3× |
| 100% | −4.7 °C | 52.4 W | 4.37 A | 52.4 W | 12.00 V | 1.0× |

## A faster PWM doesn’t help

*0.2 Hz to 20 kHz*

The first thing to try is a higher PWM frequency. It doesn’t change the loss.

A model of the legs that lets their temperature rise and fall inside each cycle pumps 9.2 W at 0.2 Hz and 9.4 W at every frequency from 5 Hz to 20 kHz. DC at the same average current pumps 16.0 W.

Above a few hertz the legs can’t follow the switching. At 490 Hz, the PWM an Arduino Uno gives on most of its pins, their temperature swings 0.03 °C. The resistive heat is the same at every frequency, because it depends only on the rms current.

**Fig. 39l: Heat pumped, by switching frequency.**

![Fig. 39l: Heat pumped, by switching frequency](https://nearfieldnotes.com/notes/peltier-pwm/fig-39l.png)

*What the figure shows:* Figure 39l: the heat pumped from a cold side held at 5 °C, with the hot side at 35 °C, by 50% PWM at 5.06 A while on, at eight frequencies from 0.2 Hz to 20 kHz, from a model of the legs that lets their temperature move within each cycle. It stays between 9.25 and 9.37 W at every frequency. DC at the same average current pumps 15.97 W.

Simulated with the cold side held at 5 °C and the hot side at 35 °C, 5.06 A while on. Below 5 Hz the legs start to follow the switching and lose a little more.

**The numbers**

| Frequency | Pumped | Drawn | Leg temperature swing |
|---|---|---|---|
| 0.2 Hz | 9.2 W | 30.6 W | 1.5 °C |
| 1 Hz | 9.3 W | 30.6 W | 1.4 °C |
| 5 Hz | 9.4 W | 30.5 W | 0.64 °C |
| 20 Hz | 9.4 W | 30.5 W | 0.32 °C |
| 100 Hz | 9.4 W | 30.5 W | 0.12 °C |
| 490 Hz | 9.4 W | 30.5 W | 0.031 °C |
| 2 kHz | 9.4 W | 30.5 W | 0.0076 °C |
| 20 kHz | 9.4 W | 30.5 W | 0.00076 °C |
| DC, same average | 16.0 W | 17.3 W | 0 |

A thermostat that clicks the module fully on and off is the same thing, slower. Holding the box at 15 °C that way averages 16.6 W. Steady DC at 0.80 A holds it on 1.9 W.

Each cycle takes about 27 minutes, and the cold side swings 17.6 °C. Ferrotec says linear or proportional control should always be chosen over on and off when the module must last.

**Fig. 39m: On and off, against steady DC.**

![Fig. 39m: On and off, against steady DC](https://nearfieldnotes.com/notes/peltier-pwm/fig-39m.png)

*What the figure shows:* Figure 39m: the average power to hold the foam box at a set temperature with a thermostat that switches the module fully on at 12 V and off, against steady DC, simulated. To hold 15 °C: 16.6 W on and off, 1.94 W steady. To hold 12 °C: 21.8 W against 3.56 W.

Simulated, with the thermostat switching 12 V at 0.5 °C of hysteresis, and real heat capacities for the cold sink, the heatsink and the cans.

**The numbers**

| Held at | On and off | Time on | One cycle | Cold side swing | Steady DC | DC current |
|---|---|---|---|---|---|---|
| 15 °C | 16.6 W | 29% | 27 min | 17.6 °C | 1.9 W | 0.80 A |
| 12 °C | 21.8 W | 39% | 24 min | 17.3 °C | 3.6 W | 1.09 A |

## Why a motor gets away with PWM

*Inductance*

Motors run on PWM all the time. A winding’s inductance smooths the current, so the motor sees steady current with a little ripple on it.

On the same 12 V, 50%, 20 kHz PWM, a stalled winding of 2 Ω and 1 mH carries 2.92 A to 3.08 A. The module has next to no inductance, so it carries all or nothing.

**Fig. 39n: The same PWM, two loads.**

![Fig. 39n: The same PWM, two loads](https://nearfieldnotes.com/notes/peltier-pwm/fig-39n.png)

*What the figure shows:* Figure 39n: the same 12 V, 50%, 20 kHz PWM into two loads, over four periods. In a stalled DC motor's winding of 2 ohms and 1 millihenry the current barely moves, between 2.92 and 3.08 A. In the Peltier module, which has next to no inductance, it jumps between nothing and 4.98 A every half period.

The winding’s current is worked out exactly, with a diode carrying it while the switch is off. The module’s is from the box simulation.

## Add the inductor

*Ripple under 10%*

So give the module the inductance it lacks. An inductor and a capacitor after the switch make it a [buck converter](https://nearfieldnotes.com/glossary/#g-buck), and the module sees steady DC.

A little ripple costs little. Resistive heat goes with the square of the rms current, so 10% rms ripple adds 1%.

Holding the same box with 10% ripple takes 7.5 W, against 7.4 W on pure DC. With 20% it takes 7.8 W. TI and Laird both put the limit at 10% ripple, and ADI notes that module makers typically do too.

At 100 kHz an inductor of about 52 µH keeps the ripple in the inductor itself to 10%, before the capacitor takes most of what is left.

**Fig. 39o: What ripple costs.**

![Fig. 39o: What ripple costs](https://nearfieldnotes.com/notes/peltier-pwm/fig-39o.png)

*What the figure shows:* Figure 39o: the power that holds the box at 7.5 °C against the current's rms ripple, from 1% to 100% of the average, simulated. Steady DC takes 7.45 W. With 10% ripple it takes 7.53 W. The line stays nearly flat to about 30% and then climbs to 29.9 W at 100%, which is what unfiltered 50% PWM is.

Simulated. The box model sees only the current’s average and rms, so any wave with the same two lands on this line. Unfiltered 50% PWM has 100% rms ripple.

**The numbers**

| Ripple, rms | Power | More than DC |
|---|---|---|
| 0.0% | 7.4 W | 0.0% |
| 1.0% | 7.4 W | 0.0% |
| 3.2% | 7.5 W | 0.1% |
| 5.0% | 7.5 W | 0.3% |
| 10% | 7.5 W | 1.1% |
| 20% | 7.8 W | 4.3% |
| 32% | 8.3 W | 11.1% |
| 50% | 9.7 W | 30.3% |
| 79% | 14.8 W | 99.1% |
| 100% | 29.9 W | 301.5% |

Make it a full bridge and the current can run either way, so the same module heats or cools.

That is how a laser in a fiber-optic transceiver stays on its wavelength. Coherent’s cooled DWDM SFP+ holds its laser within ±100 pm of its channel and draws up to 1.9 W. Coherent’s uncooled 850 nm SFP+ draws under 1 W.

The chips made for the job filter their output hard. ADI’s ADN8834 datasheet says 1 µH and 10 µF at 2 MHz hold the worst-case voltage ripple across the module under 1%.

**Fig. 39p: Two drives that smooth the current.**

![Fig. 39p: Two drives that smooth the current](https://nearfieldnotes.com/notes/peltier-pwm/fig-39p.png)

*What the figure shows:* Figure 39p: two drives that smooth the current. A buck converter: from the 12 V supply a switch and a second switch to ground chop the voltage, and an inductor L with a capacitor C across the module turn it into steady DC. A full bridge: two such legs, one at each end of the module, each with its own inductor, and a capacitor across the module, so the current can run either way.

Drawn, not simulated. In the buck the lower switch can be a diode. The full bridge follows the typical circuit in the LTC1923’s datasheet, with an inductor on each side.

## Set the duty yourself

*5% to 100%*

Pick a duty. The chart shows the current in the module and the steady DC that holds the same box, and what each one draws.

**Note 39’s explorer: Unfiltered PWM against steady DC.**

![Note 39’s explorer: Unfiltered PWM against steady DC](https://nearfieldnotes.com/notes/peltier-pwm/fig-explore.png)

*What the figure shows:* The current in the module over two switching periods at the chosen duty, against the steady DC that holds the same box, and the power each draws. Simulated.

Each duty is its own simulated run from 12 V on the 0.30 °C/W heatsink. The dashed line is the PWM’s average current.

**The numbers**

| Duty | Box | PWM average | PWM rms | PWM draws | DC current | DC draws |
|---|---|---|---|---|---|---|
| 5% | 22.9 °C | 0.29 A | 1.28 A | 3.4 W | 0.15 A | 0.07 W |
| 10% | 20.9 °C | 0.56 A | 1.78 A | 6.8 W | 0.30 A | 0.28 W |
| 15% | 19.0 °C | 0.83 A | 2.15 A | 10.0 W | 0.45 A | 0.63 W |
| 20% | 17.1 °C | 1.09 A | 2.44 A | 13.1 W | 0.61 A | 1.1 W |
| 25% | 15.4 °C | 1.34 A | 2.68 A | 16.1 W | 0.76 A | 1.8 W |
| 30% | 13.7 °C | 1.59 A | 2.90 A | 19.0 W | 0.92 A | 2.6 W |
| 35% | 12.1 °C | 1.82 A | 3.08 A | 21.9 W | 1.08 A | 3.5 W |
| 40% | 10.5 °C | 2.05 A | 3.24 A | 24.6 W | 1.25 A | 4.6 W |
| 45% | 9.0 °C | 2.27 A | 3.39 A | 27.3 W | 1.42 A | 5.9 W |
| 50% | 7.5 °C | 2.49 A | 3.52 A | 29.9 W | 1.59 A | 7.4 W |
| 55% | 6.1 °C | 2.70 A | 3.64 A | 32.4 W | 1.77 A | 9.2 W |
| 60% | 4.7 °C | 2.91 A | 3.75 A | 34.9 W | 1.96 A | 11.2 W |
| 65% | 3.4 °C | 3.11 A | 3.85 A | 37.3 W | 2.15 A | 13.4 W |
| 70% | 2.2 °C | 3.30 A | 3.94 A | 39.6 W | 2.36 A | 16.0 W |
| 75% | 0.9 °C | 3.49 A | 4.03 A | 41.9 W | 2.58 A | 19.1 W |
| 80% | −0.3 °C | 3.67 A | 4.11 A | 44.1 W | 2.82 A | 22.6 W |
| 85% | −1.4 °C | 3.85 A | 4.18 A | 46.3 W | 3.09 A | 27.0 W |
| 90% | −2.6 °C | 4.03 A | 4.25 A | 48.4 W | 3.40 A | 32.4 W |
| 95% | −3.7 °C | 4.20 A | 4.31 A | 50.4 W | 3.79 A | 39.8 W |
| 100% | −4.7 °C | 4.37 A | 4.37 A | 52.4 W | 4.37 A | 52.4 W |

## A bigger or smaller heatsink

*0.15 to 0.60 °C/W*

The heatsink moves the box’s temperature, not the verdict.

On a heatsink twice as good, 50% PWM takes 30.4 W against 8.9 W for DC, 3.4 times as much. On one half as good it is 29.0 W against 4.8 W, 6.0 times.

**Fig. 39q: 50% PWM against DC, on three heatsinks.**

![Fig. 39q: 50% PWM against DC, on three heatsinks](https://nearfieldnotes.com/notes/peltier-pwm/fig-39q.png)

*What the figure shows:* Figure 39q: unfiltered 50% PWM against the steady DC that holds the same box, on three heatsinks, simulated. On 0.15 °C per watt the box settles at 5.2 °C, PWM 30.4 W against DC 8.9 W, 3.4 times. On 0.30 °C per watt the box settles at 7.5 °C, PWM 29.9 W against DC 7.4 W, 4.0 times. On 0.60 °C per watt the box settles at 11.7 °C, PWM 29.0 W against DC 4.8 W, 6.0 times.

Simulated. On each heatsink the DC is set to hold the box where that heatsink’s 50% PWM holds it.

## How to drive one

*Three questions*

It comes down to whether the module must also heat, and whether the supply can be set.

Key to driving a Peltier module

### What goes between the supply and the module?

1. 1a It must heat as well as cool, as for a laser held at one temperature Full bridge, L and C on both sides
2. 1b It only cools Go to 2
3. 2a The supply’s voltage or current can be set Steady DC
4. 2b It runs from a fixed rail through a switch Go to 3
5. 3a The power or the heatsink’s size matters L and C after the switch, ripple under 10%
6. 3b Neither matters, as on a bench demo Unfiltered PWM works, at several times the power

The box in Fig. 39a ends at 2a or 3a. This page says nothing about the module’s life: TI ran one on PWM for five months, 3,600 hours, and saw no measurable change.

#### Conditions

- **Simulated:** Every number on this page comes from a model fitted to the TEC1-12706’s datasheet. None was measured on a bench.
- **Module:** Thermonamic TEC1-12706: 127 pairs of legs. Thermonamic gives no leg size. 1.4 × 1.4 × 1.5 mm is the size in Kryotherm’s TB-127-1,4-1,5, which has the same rating; it only sets how fast the legs follow the switching in Fig. 39l. The standard model of Lineykin and Ben-Yaakov, with the Seebeck coefficient, the resistance and the heat leak each a straight line in the module’s mean temperature. Its six numbers are fitted to the datasheet’s ratings at 27 and 50 °C and to 12 points on its curves. It gives 61.3 W, 70 °C, 6.4 A and 15.9 V, against the datasheet’s 61.4 W, 70 °C, 6.1 A and 16.0 V.
- **Fixture:** Figs. 39e to 39h: the hot side held at 27 °C, the datasheet’s test condition.
- **Box:** Room 25 °C. Fan heatsink 0.30 °C/W unless a figure says otherwise, cold sink 0.60 °C/W into the box’s air, and a foam box of about 8 liters with 25 mm walls that leaks 0.42 W per °C. 12 V supply. Settled values, except the opening figure’s 20 hours from switch-on. Fig. 39m adds heat capacities: cold sink 110 J/K, heatsink 380 J/K, six cans 8.5 kJ/K.
- **PWM:** The box model sees only the current’s average, which pumps, and its rms, which heats. That holds at any frequency fast enough that the legs’ temperature can’t follow it. Fig. 39l checks it with a model of the legs in 1-D, cold side held at 5 °C and hot side at 35 °C.
- **Motor:** Fig. 39n: a 2 Ω, 1 mH winding on 12 V, 50%, 20 kHz, with a freewheeling diode, worked out exactly in steady state.
- **Render:** Blender, to Thermonamic’s drawing. The box is an example drawn for this page.

Fitted to a datasheet. Nothing on this page has been measured on a bench.

#### Limits

- The model misses the datasheet’s heat curves by up to 0.85 W and its voltages by up to 3.2%. TEC1-12706s from other makers differ from Thermonamic’s by more than that.
- Both drives are ideal: no loss in the switch, the wiring or a converter. A real buck loses a few percent in itself, far less than the gap between the two.
- The heatsink, the cold sink and the box each have one fixed figure. Real ones change a little with temperature, and a box gets opened.
- Below 5 Hz the box model and the model of the legs part ways, because the legs’ temperature starts to follow the switching. The box figures hold above that.
- The inductor for 10% ripple is worked out by hand, from the buck’s ripple formula. It wasn’t simulated.
- Nothing here models the module’s life. Ferrotec says over 200,000 hours between failures is not uncommon on steady DC, and its own test, 7.5 seconds on and 7.5 off, gave 125,000. TI saw no measurable change after 3,600 hours of PWM.

#### Files

- sim/tec.py The module model and its fit, the fixture, the box on PWM and on DC, ripple, the thermostat, and the legs in 1-D
- sim/site.py Every duty against DC, the power for each ripple, and the motor winding
- render/scene.py The module in Blender
- render/box.py The box and its cooler in Blender

#### Sources

- [TEC1-12706 datasheet, Thermonamic’s sheet as re-badged by Conrad: ratings at 27 and 50 °C, the curves the model is fitted to, and the size](https://asset.conrad.com/media10/add/160267/c1/-/en/000189115DS02/datablad-189115-tru-components-tec1-12706-peltier-element-15-v-64-a-65-w-l-x-b-x-h-40-x-40-x-38-mm.pdf)
- [The same Thermonamic datasheet under Thermonamic’s own header, as hosted by Dessy](https://dessy.ru/include/images/ware/pdf/RDKT0083.PDF)
- [Kryotherm industrial TEC catalog, as hosted by AMS Technologies: TB-127-1,4-1,5, the TEC1-12706’s rating, with legs 1.4 × 1.4 mm and 1.5 mm tall](https://shop.amstechnologies.com/media/9f/0a/83/1720719252/Thermoelectric-Coolers-for-Industrial-Applications-Kryotherm-Datasheet.pdf)
- [S. Lineykin and S. Ben-Yaakov, “Modeling and Analysis of Thermoelectric Modules”, IEEE Transactions on Industry Applications 43(2), 505–512, 2007: the model](https://doi.org/10.1109/TIA.2006.889813)
- [TI SLUA979A, “Driving a Peltier Element (TEC): Efficiency and Aging”, 2020: constant current cooled 8.1 °C further than PWM at the same 1 A average, and five months, 3,600 hours, of PWM made no measurable change](https://www.ti.com/lit/pdf/slua979)
- [TI SLUA202A, a TEC controller with the UC3638: the LC filter, and “less than 10% ripple is recommended”](https://www.ti.com/lit/pdf/slua202)
- [TE Technology FAQ: “a ripple factor of 10% will only result in 1% degradation”](https://tetech.com/faqs/)
- [Laird Thermal Systems, Thermoelectric Handbook, 2025: no more than 10% ripple, and the temperature lost to ripple](https://lairdthermal.com/sites/default/files/fields/media.file.field_media_file/2025-01/Thermoelectric-Handbook-2025.pdf)
- [RMT, application recommendations, archived June 2026: “the PWM method always results in TE module efficiency decrease”](https://web.archive.org/web/20260617194356/http://rmtltd.ru/support/recommendations-for-use/)
- [Meerstetter, TEC controller basics: “TEC modules driven by PWM are always less efficient”](https://www.meerstetter.ch/customer-center/compendium/71-peltier-controller-tec-controller-basics)
- [Ferrotec, thermoelectric reference guide, section 10: linear or proportional control over on and off, MTBFs over 200,000 hours on steady DC, and the on-and-off life test](https://thermal.ferrotec.com/technology/thermoelectric-reference-guide/thermalref10/)
- [ADI ADN8834 datasheet: 1 µH, 10 µF and 2 MHz keep the worst-case voltage ripple across the module under 1%](https://www.analog.com/media/en/technical-documentation/data-sheets/ADN8834.pdf)
- [ADI LTC1923 datasheet: a full-bridge TEC controller whose typical circuit has a 10 µH inductor on each side of the module, and module makers’ 10% ripple limit](https://www.analog.com/media/en/technical-documentation/data-sheets/1923f.pdf)
- [Coherent FTLX3671MTCxx cooled DWDM SFP+ datasheet: ±100 pm of its channel and up to 1.9 W](https://www.coherent.com/resources/datasheet/networking/optical-transceivers/sfp/ftlx3671mtcxx-transceiver-ds.pdf)
- [Coherent FTLX8574D3BCL SFP+ datasheet: an uncooled 850 nm laser, under 1 W](https://www.coherent.com/resources/datasheet/networking/optical-transceivers/sfp/ftlx8574d3bcl-transceiver-ds.pdf)
- [Arduino analogWrite() reference, archived May 2024: 490 Hz on most PWM pins of an Uno](https://web.archive.org/web/20240526220752/https://www.arduino.cc/reference/en/language/functions/analog-io/analogwrite/)

What should the next note be? [Ask for one](https://nearfieldnotes.com/#ask-for-a-note)

---

Source: https://nearfieldnotes.com/notes/peltier-pwm/

Cite as: Michael Walker, “Peltier coolers”, Near Field Notes, Note 39, Rev 1, 14 Nov 2026. https://nearfieldnotes.com/notes/peltier-pwm/

Figures: free to reuse under CC BY 4.0 (https://nearfieldnotes.com/license/). Each one's image is linked under its name. Credit Michael Walker, Near Field Notes, and link the figure: this address plus #fig- and its number, like https://nearfieldnotes.com/notes/peltier-pwm/#fig-39a.
